Bay Windows Add Character And Area To A House

It was the ideal area. Our California cattle ranch design house had a large image window in the front space. The window extended from a couple of inches above the flooring to just a couple of inches below the cathedral ceiling. The walls and ceiling were redwood stained knotty pine and the flooring was a coordinating hardwood. The window watched out over a flower bed, shrubs and the expanse of front lawn. It was the perfect window to be replaced with a bay window.

The window was almost square. It was 72 X 72 inches. We considered a bow window, but chosen to set up a bay window instead. We just felt that our specific home looked much better with three panel bay window instead of the several panel bow windows. Our intent was to fill the seat board of the bay with potted plants we had sitting in front of the present image window. The brand-new plan would offer us a bit more space in the space and improve the general appearance of the house. It was time to shop.

Scratch vs. Pre-built

When we first understood of setting up the brand-new window, I began gathering plans for building a bay window. Thumbing through books and magazines, and the Internet search engines, I found a number of plans for building a bay window from scratch. I likewise found that carrying out such a job was going to be unnecessary. The majority of the significant window producers, such as Pella, Milgard and Anderson make both totally pre-assembled bay windows as well as pre-built elements for bay windows.

Nowadays very couple of professionals will take on the task of developing a bay or bow window from scratch. When for the exact same or less loan they can install a high quality pre-built window, it just isn’t practical. If the professionals utilize pre-built windows or components for brand-new home building and construction or remodelling projects, then we could do the same for our redesigning task, we reasoned.

Installing a bay window can easily be a do-it-yourselfer project. Before you go the diy path, however, you may desire to line up a specialist to assist out if needed.

You are likewise going to wish to line up some aid. Bay windows and window parts are heavy. At least they are too heavy for one person to handle.

Make sure and check out the weather report, consisting of the long range projection. Installing the window indicates opening a hole into your home. It can take a couple of days to get the new window in location and sealed. The last thing you want is for rain to come gathering on your floor, walls or furniture.

Make sure and examine your city or community building and construction codes. There may be special regional requirements, such as having safety glass in low profile windows. You are most likely going to require a building license anyhow, so that is likewise a great time to check the codes.

Tools and Materials Needed

The tools you will require for this project consist of a measuring tape, a framing square that you can likewise utilize as a straight edge, a circular saw or miter saw, crow bars, drill and bits, level, stapler, utility knife, tin snips and a caulking gun.

The materials you will require include the bay window unit, the support brackets, nails, roof paper, shingles, roofing nails, outside grade silicone caulking and fiberglass insulation. You will also require 1X6 inch boards for the window skirting. If you are expanding an existing window, or if you are installing the window in a space that was previously the wall, you will also need 2X4s for cripple studs and extra framing.

Basic Installation Steps

  1. Establish window position in the wall. Eliminate the existing window. Measuring the bay window, mark on the exterior of your house the opening needed for the new window. Utilizing your circular saw, cut the needed opening.
  2. Framing. Build the framing for the new window. This will likely consist of cutting through existing studs and putting in a new header, rough sill, jack studs and paralyze studs.
  3. Set up the assistance braces. A window as much as 5 feet large will take a minimum of two support braces. A wider window will need three.
  4. Set the window in location. Lift the bay window on the assistance braces and move it into the rough opening. Shim as required to level the window. Anchor in location.
  5. Develop the window roof. Set the roofing frame on top of the bay window unit and nail in location. Fill the area between the roof and the top of the bay window with insulation.
  6. Set up the window skirting around the bottom of the window. Fill will insulation and after that connect the skirt bottom to seal the beneath side of the window.
  7. Seal the edges with silicone caulking.

This is a list of the fundamental installation actions and they have been abbreviated in the interests of simpleness and space. The window system you buy will have total setup steps. When you check out and follow them, take it from the voice of experience; it truly makes the project go much more efficiently and it will be finished in much less time.

We have actually worked together on other jobs and work together well. We had the old window out and the rough framing completed on Saturday afternoon. By Sunday night we had the new window set up and the roofing and skirting finished.

And, we were right. It was the best spot for a bay window. It looked excellent from the exterior.

We considered a bow window, but elected to set up a bay window rather. We just felt that our specific house looked better with three panel bay window rather than the numerous panel bow windows. When we first got the concept of setting up the brand-new window, I started collecting plans for constructing a bay window. Most of the significant window producers, such as Pella, Milgard and Anderson make both entirely pre-assembled bay windows as well as pre-built components for bay windows.

Measuring the bay window, mark on the exterior of the house the opening needed for the new window. After all if you wan’t any trouble with your work just contact the local contractor to help your problem (